pressure main
英 [ˈpreʃə(r) meɪn]
美 [ˈpreʃər meɪn]
【化】压力总管
双语例句
- In addition, the middleware can manage these caches to reduce pressure on main memory and copy them between processors to improve workload management.
此外，中间件还可以对这些缓存进行管理，从而减少主存的压力，并能在处理器之间复制这些信息，以改善工作负载管理。 - Peer pressure is the main reason most of the kids drink.
同伴的压力常是青少年喝酒的主因。 - Spray advance angle and spray pressure is another main factor to promote the physical preparation.
加大喷油提前角和喷油压力是促进物理准备过程的另一重要因素。 - The influence of low environment pressure on the main bearing and big end bearing of internal combustion engine was investigated based on a one-cylinder diesel engine.
以立式单缸柴油发动机为研究对象，分析了低气压对发动机主轴承和连杆大端轴承工作情况的影响。 - Accordingly, under oil pressure, the main oil seal surface can work.
因此主封油面是处于油压下工作。 - The paper describes some jamming phenomena at intermediate pressure main stop valve on a600MW steam turbine, reasons are analyzed and some effective methods are carried out.
描述了某600MW机组中压主汽门的卡涩现象，对各种原因进行了分析，并采取了切实有效的处理方案。 - This relieved the pressure on the main dyke.
这减轻了对主堤的压力。 - Investigation and analysis of pressure load in main caregivers of primary hepatic carcinoma patients in advanced stage
能力利益，能力限度照顾原发性肝癌晚期病人主要照顾者压力负荷调查分析 - It mainly includes a hydraulic pressure main engine, a stripping power supply, a male die, two female die composite units together with a lining board and a parison push-out mechanism.
主要包括液压主机、脱模电源、阳模、连同衬板在内的两个阴模组合体、型坯顶出机构。 - Using Reynolds equation to derivate the formula for calculating bearing pressure distribution, then calculate pressure distribution of main bearing shell of tube mill on the basis of this formula.
本文用雷诺方程推导出计算轴承压力分布的差分公式；并以此为依据，计算管磨机主轴承轴瓦的压力分布；并为轴瓦的结构设计提出建议。 - Causation to Fault Close of 330 MW Unit High Pressure Main Stop Valve and its Measure for Solution
330MW机组高压主汽门故障关闭的原因及解决措施 - Treatment to Control Oil Leakage Fault of Steam Turbine High Pressure Main Throttle Valve
汽轮机高压主汽门控制油泄漏故障处理 - The common ones are "hard interlock"-between oil pump motor and main motor and "flexible interlock"-between oil supply pressure and main motor.
主轴承供油联锁系统常见的有油泵电机与主电机之间的“硬联锁”和供油压力与主电机之间的“软联锁”。 - The rolling emulsion and oil pipe form a closed system with the cooler, filter and indicator for pressure of the main pipe.
轧机乳液和油路自成封闭系统，具有冷却、过滤和总管压力指示功能。 - With the further development of Shanghai city gas industry, especially the phenomenon that natural gas enters Shanghai downtown area step by step and the continuous increasing of gas clients, the big inch medium pressure main gas pipe hatched grafting branch pipe constructions become high frequency.
随着上海城市燃气事业的进一步发展，尤其是天然气逐步进入上海市区，燃气客户的不断增加，大口径中压燃气主管道镶接分支管的施工日益频繁。 - Testing of the Dynamic Parameters for Air-static Pressure Main Shaft System
空气静压主轴系统的动态参数测试 - A kind of newly structure, performance stable with highly accuracy air static pressure main axle is developed.
研制出一种结构新颖、性能稳定的高精度空气静压主轴。 - The greasing ( interval) time and monitoring time are set by using the monitor, the pressure in main lines is detected and the pump operating time is adjusted by using the pressure sensor in order to carry out auto-greasing timing and fault alarm function for lubrication system.
通过监控仪进行加脂间隔时间和监控时间的设定，通过压力开关检测主油路工作压力，并对油泵的工作时间进行自动调节，实现系统的定时自动加脂与故障报警功能。 - These factors are: the fiber-gypsum ratio, the layer height of material, the speed of continuous pressing machine and the pressure of main pressure rollers.
影响板厚的因素主要有：混和物料的木膏比、铺装机的铺料高度、连续式压机的速度以及压机主压辊压力等。 - Cause Analysis of the Jamming at Intermediate Pressure Main Stop Valve and its Modification
中压主汽门卡涩的原因分析及对策 - Wall-thickness of steel pipe for water transmission in America is designed based on inside hydraulic pressure as main parameter.
美国输水钢管壁厚的设计是完全的柔性管理念，其管厚设计计算公式是以内水压为主要参数来考虑的，外压作为核校条件。 - CONCLUSION Increased intracranial pressure is main cause of respiratory system complications.
结论并发呼吸功能障碍的主要原因是颅内压增高。 - Finally, the vectoring angle increases with the increasing of the ratio of secondary fluidic injection pressure to main flow pressure.
°气动矢量角随次主流压比SPR的增大而增大。 - The wall plate hydraulic pressure shaper main traverse structure optimization designs
墙板液压成型机上横梁结构优化设计 - Working performance of high effective synchronous pressurization hydraulic system of multi-cylinder press with large table has been introduced with calculation of design of system pressure and main components.
介绍了大台面液压机的多缸同步高效加压液压系统的工作特点，并对系统压力和主要部件进行了设计计算。 - Cause Analyzing of the Turbine Running High Pressure Main Stop Valve Shut Suddenly from the Full Open Position
汽轮机高压主汽阀运行中由全开突关的原因分析 - Measurement of Static Differential Pressure for Main Fan Flowrate Static Pressure Molding Machine
主通风机风量的静压差测定法 - In polyester package dyeing the dye bath, under the pressure of main pump, penetrates into the package, leading the dyestuffs absorbed by the fibre and diffuses then into the inside of the fibre at a certain temperature.
涤纶筒子纱染色是在一定的温度下，利用染色机主泵的压力作用使染液穿透筒子纱线，染料被纤维吸附并向纤维内部扩散，从而达到上染的目的。 - Analysis on Leakage of High Pressure Main Steam Valve Lever
高压主汽阀阀杆漏汽原因分析